Sparkfun Thing Plus RP2040
The Sparkfun Thing Plus RP2040 is a tiny development board based on the Raspberry Pi RP2040 microcontroller.
Peripherals:
- ws2812 Neopixel
- sdcard
Interfaces
| Interface | Hardware Supported | TinyGo Support |
|---|---|---|
| GPIO | YES | YES |
| UART | YES | YES |
| SPI | YES | YES |
| I2C | YES | YES |
| ADC | YES | YES |
| PWM | YES | YES |
| USBDevice | YES | YES |
Pins
| Pin | Hardware pin | Alternative names | PWM |
|---|---|---|---|
GP0 |
GPIO0 |
UART0_TX_PIN, UART_TX_PIN |
PWM0 (channel A) |
GP1 |
GPIO1 |
UART0_RX_PIN, UART_RX_PIN |
PWM0 (channel B) |
GP2 |
GPIO2 |
SPI0_SCK_PIN |
PWM1 (channel A) |
GP3 |
GPIO3 |
SPI0_SDO_PIN |
PWM1 (channel B) |
GP4 |
GPIO4 |
SPI0_SDI_PIN |
PWM2 (channel A) |
GP6 |
GPIO6 |
I2C0_SCL_PIN, I2C1_SDA_PIN, SDA_PIN |
PWM3 (channel A) |
GP7 |
GPIO7 |
I2C0_SDA_PIN, I2C1_SCL_PIN, SCL_PIN |
PWM3 (channel B) |
GP8 |
GPIO8 |
PWM4 (channel A) |
|
GP9 |
GPIO9 |
PWM4 (channel B) |
|
GP10 |
GPIO10 |
PWM5 (channel A) |
|
GP11 |
GPIO11 |
PWM5 (channel B) |
|
GP12 |
GPIO12 |
SPI1_SDI_PIN |
PWM6 (channel A) |
GP14 |
GPIO14 |
SPI1_SCK_PIN |
PWM7 (channel A) |
GP15 |
GPIO15 |
SPI1_SDO_PIN |
PWM7 (channel B) |
GP16 |
GPIO16 |
PWM0 (channel A) |
|
GP17 |
GPIO17 |
PWM0 (channel B) |
|
GP18 |
GPIO18 |
PWM1 (channel A) |
|
GP19 |
GPIO19 |
PWM1 (channel B) |
|
GP20 |
GPIO20 |
PWM2 (channel A) |
|
GP21 |
GPIO21 |
PWM2 (channel B) |
|
GP22 |
GPIO22 |
PWM3 (channel A) |
|
GP23 |
GPIO23 |
PWM3 (channel B) |
|
GP25 |
GPIO25 |
LED |
PWM4 (channel B) |
GP26 |
GPIO26 |
A0, ADC0 |
PWM5 (channel A) |
GP27 |
GPIO27 |
A1, ADC1 |
PWM5 (channel B) |
GP28 |
GPIO28 |
A2, ADC2 |
PWM6 (channel A) |
GP29 |
GPIO29 |
A3, ADC3 |
PWM6 (channel B) |
Machine Package Docs
Documentation for the machine package for the Sparkfun Thing Plus RP2040
Flashing
UF2
The Sparkfun Thing Plus RP2040 comes with the UF2 bootloader already installed.
CLI Flashing
-
Flash your TinyGo program to the board using this command:
tinygo flash -target=thingplus-rp2040 [PATH TO YOUR PROGRAM] -
The Thing Plus RP2040 board should restart and run your program.
Troubleshooting
Any troubleshooting tips go here.
Notes
You can use the USB port to the Thing Plus RP2040 as a serial port.
The Neopixel LED and the SD Card are supported by tinygo drivers